by
The flexible support is round steel.
7-7.
Description ■ the crane beam is a load-bearing member of the crane load, which is welded by steel plate.
Frame column frame column can adopt H-shaped section, box section, cross section, circular tubular section, etc.
portal frame with crane C.
Multi storey frame system 1-2-1.
Hv-225td-900 plate 7-6-1, plate type diagram 7-6-2, description of connection node diagram: ■ waterproof cavity can prevent water seepage caused by capillarity.
Basic node A.
c.
Frame diagram 1-2-2.
1-2.
The support and tie rod rigid support are made of hot-rolled section steel, generally angle steel.
b.
■ in multi-storey frame system, horizontal corner brace is often set at the position of beam column rigid connection.
beam and column node ■ local second floor node refers to multi-storey frame system.
6.
column base node B.
1.
Figure 4-1.
■ this plate type is used for wall panel and is connected with roof purlin or wall beam by self tapping screws; The screw is fixed with the wall beam at the straight section of the wave trough near the wave crest.
Hv-205td-820 plate 7-5-1, plate type diagram 7-5-2, description of connection node diagram: ■ waterproof cavity can prevent water seepage caused by capillarity.
3.
d.
Basic form of portal frame A.
The force on the floor and roof is transmitted to the frame column through the frame beam.
■ the method of roof horizontal support is the same as that between columns.
Rigid frame columns and beams are made of H-section steel, and various loads are transmitted to the foundation through columns and beams.
column base node ■ column base node is the same as portal frame system.
1-1-3.
Basic node A.
The flexible support is made of round steel and must be tensioned during installation.
Column and beam node 2, support, tie rod 2-1, flexible support between columns shown in the figure, rigid support between columns 2-2.
■ when the crane tonnage is large, set the brake truss or brake beam to resist the transverse horizontal load.
The figure shows the standard crane beam structure of the middle span of the crane beam.
Hv-360yc-360 plate 7-7-1, plate type diagram 7-7-2, description of connection node diagram: ■ self tapping screw passes through the plate and is directly connected with the wall beam..
Rigid connection – supporting frame: rigid connection is adopted in the transverse direction, hinged connection is adopted in the longitudinal direction, and support is set in the longitudinal direction to transfer horizontal force.
Bear the force transmitted from roof panel and wall panel, and transmit the force to columns and beams.
Frame beam frame beam generally adopts H-shaped section.
■ when used as roof panel, the screw passes through the wave crest and is fixed with the roof purlin; When used as a wall panel, the screw is fixed with the wall beam in the straight section of the wave trough close to the wave crest.
Hv-197td-788 plate and hv-205td-820 plate are used as profiled steel plate for rain canopy.
5.
■ according to the needs, the support can also be herringbone, splay, K-shaped, V-shaped, door shaped, L-shaped, Y-shaped, single inclined rod and other forms.
When there are rigid members at the support end and transmit pressure, it is not necessary to set tie rods.
Corner brace 3-1, figure 3-2, description ■ the setting of corner brace is the calculated length out of plane of the compression flange of beam or column.
1-2-3.
The rigid support is made of section steel and is used in structures with high stiffness requirements such as multi-storey frame and lower section support of crane beam.
Roof purlins and wall beams are generally C-shaped steel and Z-shaped steel.
pure rigid frame: rigid frame is adopted in both vertical and horizontal directions.
1-1-5.
Description ■ support is divided into flexible support and rigid support.
Purlin, wall beam 6-1, C-type cold-formed thin-walled section steel 6-1-1, section characteristics of section steel 6-1-2, installation node figure 6-2, Z-type cold-formed thin-walled section steel 6-2-1, section characteristics of section steel 6-2-2, installation node Figure 7, roof and wall profiled steel plate 7-1, hv-203kl-406 plate 7-1-1, plate shape figure 7-1-2, connection node figure 7-2, hv-380sf-7607-2-1, plate shape figure 7-2-2, connection node figure 7-3, hv-475sf-475 plate 7-3-1, plate shape figure 7-3-2, connection node figure 7-4 Hv-197td-788 plate 7-4-1, plate type figure 7-4-2, connection node Description: ■ waterproof cavity can prevent water seepage caused by capillarity.
The corner brace can be made of angle steel or pressed by flat steel.
The tie rod is a compressed circular steel pipe, which forms a stress closed system with the support.
■ this plate type can be used for roof panel and wall panel, and is connected with roof purlin or wall beam by self tapping screws.
typical portal frame B.
7-4.
■ refer to the side span structure for the treatment of deformation joint position.
All superstructure forces are transmitted to the foundation through frame columns.
Building system 1-1, portal frame system 1-1-1, basic components figure 1-1-2.
■ this plate type can be used for roof panel and wall panel, and is connected with roof purlin or wall beam by self tapping screws.
Sometimes, in order to ensure sufficient stiffness, supports are also set in the rigid frame.
Explain the mechanical principle.
The portal frame structure is mainly a horizontal rigid frame composed of columns and beams, and the rigid frame is a plane stress system.
■ when used as roof panel, the screw passes through the wave crest and is fixed with the roof purlin; When used as a wall panel, the screw is fixed with the wall beam in the straight section of the wave trough close to the wave crest.
Braced frame: hinged is adopted in both vertical and horizontal directions, and supports are set in both directions to transmit horizontal force.
The support is generally made of hot-rolled section steel, and its function is to transfer the horizontal force between layers and ensure the stiffness of the structure.
b.
Crane beam 4-1.
4.
Description of mechanical model a.
Derived form of rigid frame ■ crane and local second floor can be arranged in the derived form of rigid frame.
In order to ensure longitudinal stability, inter column support and roof support are set.
7-6.
■ gable rigid frame is also a multi span rigid frame in essence, but the middle column and rigid frame column rotate 90 degrees compared with the section.
It is mainly used for portal frame structure.
■ tie rod and support work together to form a closed stress system.
portal frame with local second floor 1-1-4.
